Skip to main content

13W x 4 Audio Amplifier with Surround Sounds


This is my new audio power amplifier which is based on TDA8511 power amplifier IC. According to the datasheet this IC produces 13W per channel (with 2R load) and single TDA8511 chip contain 4 inputs and outputs.

Other than TDA8511 this amplifier use TA8184 for tone controls and LA2610 for surround sound processing.

To obtain the high sound quality and good separation I use separate amplifier module for each tweeter and woofer in both left and right channels. (That’s why I’m select TDA8511 for this project)

For the test run I couple this amplifier with my JVC DVD Player and it produces extreme high quality audio output.

Front Panel controls available in this amplifier are,

  • Volume
  • Bass
  • Treble
  • Balance
  • Surround Sound On/Off
  • Loudness Switch
  • Power On/Off

Some of the calculated technical specifications are,

  • Output Power : 13W x 4
  • Supply Voltage : 15V Single Rail
  • Total Harmonic Distortion : 1%
  • Bass Control Range : -12.5dB to +12.5dB
  • Treble Control Range : -12.5dB to +12.5dB

Comments

Post a Comment

Popular posts from this blog

Building the TD4 4-Bit CPU

The TD4 is a famous 4-bit CPU featured in the book How to Build a CPU by Kaoru Tonami . The book focuses on constructing a functional processor entirely from basic 74-series TTL logic ICs. While the book is unfortunately only available in Japanese, a friend from Japan sent me a copy along with a TD4 PCB. I believe the PCB is based on the open-source design files available on BG5DIW's GitHub repository . "How to Build CPU" book and the PCB. Recently, I finally found the time to build and experiment with it. The project took a few months, as I had to translate the book myself to grasp the core concepts. The overall design is simple and elegant, offering a set of 12 instructions and a 16-byte ROM (implemented via DIP switches) for programming. The board operates on 5V and can be powered via USB. Most components were sourced from local shops, though I had to order a few 74HC-series ICs online. Later, I tested the circuit by replacing some 74HC components with 74LS series...
Post a Comment
Read more

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...
3 comments
Read more

AVR-HV: High voltage programmer for AVR microcontrollers

When it comes to AVR microcontrollers the most common programming option is In-System Programming ( ISP ). ISP interface is easy to use but in some scenarios it is totally unusable. The most common scenario is with some wrong fuse bit values. For example if we program SPIEN or RSTDISBL fuse bits, AVR microcontrollers may not respond to any in-system programmer(s). To overcome these problems the next available option is high voltage programming mode. In High voltage programming mode, 12V programming voltage is applied to RESET pin of target AVR microcontroller and user can change configuration fuses of AVR MCU with minimum amount of risk. The only drawback in this mode is that target microcontroller must need to be removed from the board to reprogram. Most of the AVR high voltage programmers are expensive and difficult to find in ordinary electronic shops. As a solution we implement USB base high voltage parallel programmer for AVR microcontrollers and it allows programming, readi...
1 comment
Read more