Home-produced USB Sound Card

In this project I’m build USB sound card using single chip and it produce good audio output and compatible with Windows 9x operating systems and Windows NT family operating systems (I am not tested this circuit with Windows Vista and chip manufacturer say it is worked with Mac OS also) This is a plug and Play device and device driver is not required. Special feature of this sound card is its built-in HID controller. Using this HID controller user may be able to control Windows Volume control using 3 buttons located on the sound card. These buttons are used for Volume Up, Volume Down and for Audio Mute.

This device is based on Burr-Brown’s PCM2904 USB CODEC chip and it produces stereo output. PCM2904 operates using USB power (self powered) and external power adapter is not required.

I think this device is ideal for USB headphones or mini-speaker modules. My implementation is 10x9 cm. I spend Sri Lankan Rs. 1500 for this circuit.

Comments

clee1 said…

I would be very interested in your schematic; the one contained in the data sheet did not answer all my questions, specifically as regards to HID functions. I am planning to use the pcm2904 in a PC-to-Ham Radio tranciever interface for use with digital radio modes.

September 30, 2008 at 10:43 AM

Dilshan Jayakody said…

I’m use the schematic available in datasheet with some minor modifications (specially in audio output section to match the impedances) To send the exact schematic first I need to draw it, and it is bit time consuming, but if you need it I’m draw and send it to you. Please drop me some mail. (jayakody2000lk@gmail.com)

October 6, 2008 at 7:45 AM

Anonymous said…

woww

June 14, 2010 at 7:14 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M