433MHz RF remote control system for RC Cars

After the 2 weeks of continues development we finally design suitable RC remote control system for cars. This RC system has,

Battery eliminator circuit (BEC)
Control System
433MHz transmitter and receiver module
Motor driver and servo controller

In this design both transmitter and receiver modules are based on seeed studio’s 433MHz RF link kit and control systems are based on microchip’s PIC16F84A MCU.

At the design time we test this circuit with Futaba, Airtronics, JR-Radios, HiTec and "Mystery" (available in eBay) micro-servo units. This circuit may support standard electric motors (brushed DC motors) and during the testing stages we drive RC helicopter motors and RC airplane motors successfully with this system. To drive this circuit we use 7.2V 500mAh Li-Po batter pack.

During the circuit assembling and testing, make sure to take necessary actions (e.g: shielding) to prevent/minimize the EM interferences which was generated by the motors. Most of the time these EM noises may reduce the performances of the 433MHz receiver module.

To get the maximum performance use 830mm (or higher) telescopic antenna with the transmitter and 20cm antenna with the receiver.

We design this system for RC cars but it can also use with RC airplanes, helicopters and boats with some minor modifications to the receiver module.

All the circuit diagrams and MCU source codes are available to download at here.

Comments

Rc-Fly said…

If you like this article maybe you also like some article in my site
Please visit here

July 24, 2009 at 2:23 PM

EnrgTech said…

Visit us here for details about PRO-LORAT16-8S10

November 11, 2019 at 4:48 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...