4 Channel Remote Control Video Switch

In this project we developed 4 inputs (Audio and Video), remote control operated video switch for general home use. This design is mainly based on Microchip PIC16F630 8bit MCU, 4052 differential 4 channel analog multiplexer, TSOP1838 infrared receiver module and 7447 BCD to seven segment decoder. With a given schematic and PCB design users can switch 4 different audio and video sources using compatible remote controller. Current version of this project is work only with most of Sony remote controllers (which based on Sony SIRC protocol) and it can be easily extend to Philips RC-5 protocol with some minor modifications of PIC16F630 software system.

In this design we incorporate small single transistor video amplifier to its output stages to amplify the (chroma) part of video signal. Audio output stage of this system may not need any AF amplifier. (In the designing stages we notice some clipping of input signal in 4052 analog multiplexer, but it is not much noticeable in practical environment/use.)

At the time of testing we use Sony RMT-V408 remote controller with this project and it produces successful results. Basically this project support only numerical keys between 1 to 4 and program Up/Down (+/-) buttons of remote controller.

This system is design to work with 5V supply voltage and to get the optimal results it is highly recommended to use well-regulated 5V – 750mA power supply with this unit. To reduce the interferences place screen-wires to both audio/video input/output lines and place them separately from AC main-lines and PSU transformer(s).

Note : With the given source code system may respond to any, compatible Sony SIRC protocol base remote controller, but this may get some problems in practical environment. To avoid this problem please validate the value of remote_sys variable with your target remote controller. In here I’m not implement it because I do not have any Sony SIRC protocol compatible products.

The complete schematic, source code and PCB designs of this project is available to download at google drive.

Comments

Rack mount Monitor said…

Hey, Nice and quality information provided by you. But there are some updated video switch you can find at http://www.smartvm.com/video-switches-c1293.htm.

September 13, 2010 at 8:54 PM

viagra online said…

nice

July 1, 2011 at 8:02 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...