Homemade ADSL Splitter

Nowadays DSL splitter is a common unit in telecommunication and it is used by most of the ADSL users to obtain the maximum performance of the connectivity. Technically DSL splitter is an analog LPF (low pass filter) which is used to prevent interferences between analog telephone device(s) and DSL support units.

In this project we describe how to build miniature ADSL splitter at home with grater simplicity and with minimum amount of cost. To build this unit user need to use few generic components which include pairs of 330µH inductors and 1R resistors, 0.0033MFD capacitor and three units of RJ11 PCB connectors.

We successfully test this splitter with our local ADSL connection and it gives equal performance of commercial DSL splitter.

The complete schematic and PCB diagram (Eagle) of this ADSL splitter is available to download at google drive

Comments

Apoorva said…

Hi Dilshan,
Thanks for sharing the circuit.
I have 4 nos. of broken adsl splitter in my drawer. Was not able to find which terminals goes where.So i went on buying new ons each time. Now thatI have yr circuit I understood the wiring. I will now repair all 4 and use them. Thanks again. - Apoorva India

August 22, 2010 at 4:52 PM

sri lanka said…

Thanks a lot Dilshan . As sri lankan I'm proud about you

August 20, 2011 at 9:42 AM

බුද්ධික said…

Thanks bro!!! This helped me to fix mine too,
here is the my blog post :)

http://lab.buddika.info/2012/04/adsl-splitter-quick-fix.html

April 8, 2012 at 10:39 AM

MaNo said…

Thanks for providing such a valuable circuits....

July 4, 2012 at 12:10 AM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...