Skip to main content

Electric Fence with Automated Monitoring System

Electric Fences are designed to create an electrical circuit when touched by person (or animal). The circuits proposed in this article release 10kV electrical pulses to the fence-line and monitor the line status. This entire system is design to drive using 25V (5A) single-rail DC power source (using 5A power supply unit or pair of 12.6V Lead-Acid batteries).


Main controller of this system is Microchip PIC12F675 – 8bit microcontroller. All the line monitoring, pulse generation and alarm system controlling is performed by this microcontroller.

Some of the most notable features of this system are built-in audible alarm system, contactless fence line monitoring system, Support for wide range of step-up transformers (up to maximum of 10kV) and compact 10cm × 10cm PCB design.

This system use standard electronic components (through-hole components) and SMD components in this provided PCB layout. All the project documents, schematics, PCB designs and firmware source codes are available to download at google drive.
Labels:

Comments

xlpharmacy said…
Electric fences are very effective, I got one to protect my farm off the vegetables robbers and animals who like to wander around, but it is extremely important to be precise on the charge of it, cause otherwise, it could end up in a very awful incident. (Experience talking here by the way)
July 1, 2011 at 9:53 PM
Post a Comment

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...
2 comments
Read more

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...
Post a Comment
Read more

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...
5 comments
Read more