PIC16F877A/PIC16F887 Microcontroller Development Board

In this post we introduce easy to build, full featured PIC16F877A/PIC16F887 microcontroller development board. This development board contains following core features:

RS232 interface
PS/2 host interface
Battery backup - Real Time Clock with I2C interface
Highly precision 1-wire thermometer interface
4 Digit Seven Segment Display module
HD44780 compliant LCD module
4×4 Keyboard
4 button onboard joystick
8×2 LED driver
8bit peripheral driver interface
8bit Digital to Analog converter module
36kHz Photo module for Infrared base inputs
Wide supply voltage range from 12V – 40V

To reduce the form-factor we design this system in a double sided PCB. When constructing this project make sure to use exact component values for PSU module (especially for L1, R1 and R2).

When constructing the circuit do not connect R4 and R5 wires to the PCB. Both these wire links are providing to isolate the PSU from main board. After constructing the circuit power on the PSU and check the voltage between R4 and R5. Under normal operating mode voltage between R4 and R5 is 4.8V – 5.03V.

LM2576-5.0 is also compatible with this board. If IC1 is LM2576-5.0, make sure to replace R1 with wire and open R2 resistor in the PCB.

It is required to install suitable heatsink to the LM2576 switching regulator. 20V (3A) D.C. power source is recommended for this PSU.

This development board is compatible with any HD44780 compliant LCD module. While at the testing stages we check this LCD interface with several 1602E-1 LCDs and all these modules provide excellent results to us.

This development board is released as an open hardware project and licensed under the Creative Commons Attribution-ShareAlike 3.0 license.

All the project schematic files and PCB designs are available to download at google drive.

Comments

Unknown said…

Hi,
May I know from where we can buy these electronic components to construct the circuit?
thank you

January 13, 2013 at 9:22 AM

Dilshan Jayakody said…

All the components in this circuit are available to buy in following places:

- Most of the electronic component shops in Petta - Sri Lanka, and other places.

- If you are looking for excellent quality parts try Farnell - Sri Lanka.

- Through eBay

January 13, 2013 at 1:13 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...