Microprocessor controlled CW Beacon

In this project we introduce portable microprocessor controlled CW radio beacon. This CW beacon module is capable to transmit maximum of 64 Morse codes repeatedly in 4.433MHz with 9V DC power source.

This system consists of CW transmitter, ATtiny13 microcontroller unit and low current voltage regulator. Atmel ATtiny13 microcontroller is used to drive the transmitter and thanks to its internal 64 byte E²PROM, we may be able to change beacon data without altering the system firmware.

While at the testing stages we receive this beacon on 10km radius (using Sony ICF-SW7600GR receiver) by using standard telescopic antenna. To get the maximum range it is recommended to use 3m – 4m antenna wire with this transmitter system. At the prototyping /testing stages we try this transmitter successfully with 3.58MHz, 4.43MHz and 6.00MHz crystals.

This system is design to work with standard 9V battery (6F22/6LR61). At the prototyping stages we test this system using 12V and 10V DC power sources and get the same results.

Transmitter of this system is based on Nyle Steiner’s (K7NS) "80m CW transmitter" unit. All the project source codes, schematic diagrams and PCB patterns are available to download at elect.wikispaces.com.

This project is released as an open hardware project and all the source codes are licensed under the terms of GNU General Public License Version 3 and all the documents, schematics and PCB patterns are licensed under the Creative Commons Attribution-ShareAlike 3.0 license.

Comments

Samsung Printer Toner Cartridge said…

Very impressive and I truly hope that it will work the way it is supposed to do.

October 2, 2011 at 1:10 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M