Simple 8bit digital data logger using PIC16F887

This is an example application for our "Extend PIC Microcontroller‘s RAM by without using EMI" blog post. In this system PIC16F887 microcontroller is interface with four units of UM61512AK – 64K × 8 CMOS SRAMs. Monitoring signal is supplied to the MCU through “PORT A” and all the communications are performing through RS232 interface.

In my previous post most of the readers ask me about pure C language routine(s) for memory access. To fulfill that request I rewrite both memory read and write operations using C programming language. Compared with the previous Assembly language routines, only performance glitch in this implementation is 16bit address decoding part (which consume some CPU cycles than assembly language implementation)

With this given firmware user can operate this system by without installing any driver software in the host side. All the data capturing and reporting operating are done by MCU itself.

Originally I design this data logger to do some photometric data logging. To generalize and to simplify I remove photo-detection and low voltage amplifier from this design.

This is an open hardware project. All the firmware source codes are released under the terms of GNU Lesser General Public License (LGPL) 3.0 and all the documents and other resources are released under the terms of Creative Commons Attribution-ShareAlike 3.0 Unported License. Downloadable content of this article are available at google drive.

Comments

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M