Skip to main content

Offline High Voltage AC Power Supply

This is a high voltage, low current, offline, AC adjustable power supply for electronic/electrical experiments. This power supply is mainly design for switch mode power supply (SMPS) experiments and to drive basic high voltage electrical circuits. Thanks to the isolated step-up transformer this power supply breaks the ground loop and provides shock free – safer high voltage output. This offline (or isolation) feature preventing accidental current from reaching ground through a person's body.

This unit generates 50Hz or 60Hz (selectable at runtime) square wave AC output, and it is capable of generating output voltage between 150V – 290V AC (on no-load state).

Prototype version of offline high voltage AC power supply

As stated above this power supply unit is mainly design for SMPS experiments. This is not work well with liner power supplies because transformers in linear power supplies are get overheating from square wave inputs generated through this unit.

This is a high voltage project. Make sure to insulate all the connections, and install this unit in a "high voltage safe" enclosure. Before applying power make sure to check all your connections and external wirings.

This is an open hardware project. All the project schematics, wiring diagrams and PCB designs are available to download at here.

Please note that this power supply is design for low current – high voltage experiments. Do not attempt to drive your refrigerator or electric drill through this unit.
Labels:

Comments

Emily said…
Hello, I'm an electric engineer & I'm engaged in making Ac Dc Adapter for last 10 years. Actually, maximum efficiency is a prime consideration for all SMPSs, but even more so for those found in portable devices, where battery life must be prolonged to offer consumers extended run time while using their favorite gadgets and toys. High efficiency is also a must for those designs that require improved thermal management, or where the cost of providing power is of concern.
Thanks:)
September 19, 2012 at 7:33 PM
Diana- power adapter said…
I've come up with a circuit using a flyback transformer (from an old computer monitor) and a 555 timer that charges the caps significantly faster, but I'm still working out the bugs. My current version has a flyback with a 15 turn primary and a 400 turn secondary. I used 22awg on the primary and 28awg on the secondary.It charges to 380v in about 10 seconds with a 13.8v input (could use a zvs driver for more power). I need to get some high speed diodes to rectify the output. I have been using 1N4007's but they are too slow. I will get some UF4007's instead. thanks!
--------------
visit my website
April 26, 2013 at 4:29 PM
Post a Comment

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist
2 comments
Read more

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ
Post a Comment
Read more

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M
5 comments
Read more