24-bit Stereo Audio DAC for Raspberry Pi

This project is about 24-bit stereo DAC, which we build for Raspberry Pi boards. This R-2R ladder DAC is developing around Intel / Altera EPM240T100C5N CPLD.

We developed this module after review the PT8211 DAC, which we tested a few months ago. Compare with PT8211 DAC, this module is capable to provide high-quality audio output with Raspbian OS.

A finished prototype of the R-2R DAC.

At the testing stages, we drive this DAC with the I²S bus of the Raspberry Pi 3 Model B board. The provided device tree overlay is developed and tested on the new Raspbian Buster OS.

The audio quality of this DAC is impressive. In most of the circumstances, we test this unit using mpg123 player and got excellent results.

The MCP602 opamp of this module is capable to drive a headphone, and for the testing, we use Audio Technica ATH-PRO500MK2BK headphones directly with this module. Also, we pair this module with several AF power amplifiers and obtained superior results. The most noticeable AF power amplifiers which offer excellent results with this system are based on STK4221, LM3886, and TA2020 ICs.

To minimize the cost, we use small SMD components with this PCB. Most of the components of this PCB design are on (1608) 0603 packages. To avoid short-circuits, and damages we recommend to assemble this PCB using SMD rework station.

This is an open hardware project. All the contents including RTL source codes, configuration scripts, schematics and design files of this project are available at the GitHub repository.

Comments

Mio Taalas said…

Sure it's great for educational purposes and to learn stuff, but it's not really 24bit since you'll lose quite a bit (pun intended) for noise in the resistors themselves and in general noise since the surface area of the board and DAC is quite large. Not to even mention powersupply noise etc. etc.

Nice project regardless... you could talk about the drawbacks and the real performance as well so people get better understanding on how difficult it is to design DAC's :)

January 19, 2020 at 1:06 AM

Alfred Avina said…

The article is so appealing. You should read this article before choosing the Big Data Implementation Services you want to learn.

February 29, 2020 at 10:51 AM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner frequ

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M