Low cost TEA5767 based FM stereo radio receiver

TEA5767 is electronically tuned FM stereo radio receiver comes from NXP for low voltage applications. TEA5767 based radio modules are now common in the field and this project is based on Samsung TT-502 radio module. The main objective of this project is to design low-cost FM tuner based on this TT-502 / TEA5767 module and commonly available electronic components.

In this receiver the main controller is ATmega8 MCU, except to that TDA2822 is used as AF power amplifier, PT2257 is used to control the volume. In this given design MCU, PT2257 and TEA5767 radio module are set to work with a 3.3V power source. The LD33V voltage regulator is used to obtain 3.3V from the supply voltage.

To control the receiver, MCU provides five push buttons. Those can be used to control volume, perform an automatic scan and manual tuning.

The final version of TEA5767 based FM radio receiver.

The firmware of this receiver is developed using MikroC for AVR and it is available to download with project package.

This receiver is design to drive using 9V - 12V DC power source and we recommended using regulated AC power supply to drive this tuner.

While at the testing we got very good results with this tuner and it performs similarly to the commercial grade portable FM stereo radio receiver. All the schematic and firmware related to this project are available to download at google drive.

Comments

Kaito Powered Solar Power said…

Your blog is really awesome, thank you so much for sharing with us this valuable information.

April 26, 2019 at 4:34 PM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...