CoCA Emerge + Tech - Musical plants project

CoCA "Emerge + Tech" - Musical plants is an electronics, software and plants base exhibit we developed for Cinnamon Colomboscope 2016 exhibition. This installation will feature a touch-sensitive sensor that will generate a soothing sound from each plant. By interacting with individual plants, the audience can create musical compositions.

The sensor unit of this project consists of 14 high sensitive, configurable level detectors and USB interface. In this sensor unit, we use Samsung's KA2284 as an amplifier, level detector, and PIC18F4550 8-bit MCU as data multiplexer and USB I/O controller. PC817 optoisolators are used to interface between analog front-end and digital data processor. In this design, both analog and digital circuits are physically and electronically isolated to minimize the noises and interferences.

In this design, we use KA2284 because it is commonly available in the local market (in Sri Lanka) and costs less than 0.1 USD. To reduce the interferences we use shielded cables between plants and sensor ICs. With the special wire, we are using we may be able to extend the sensor connectivity up to 3m.

Sensor board of musical plants project.

PC application of this project is developed by using HIDAPI and irrKlang libraries. This application is designed to work with Microsoft Windows operating systems and we tested it on Windows 7 and Windows 10.

This project is an open source hardware project released under terms of MIT and CC BY-SA licenses. All the content of this project is available to download at hackaday.io or github.com. Conceptual details of this project are available at CoCA homepage.

Comments

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...