Extending the frequency range of Pioneer TX-7700 tuner

TX-7700 is AM/FM stereo tuner manufactured by Pioneer in around 1975 - 1980. This is a basic tuner system which is specifically designed for "rack style" stereo systems. Compare with other tuner systems this tuner is not very popular and very limited information is available on the internet about this model.

This tuner is mainly built around HA1138 AM radio receiver, HA1156 stereo decoder and PA3001 (HA11225) FM IF amplifier IC.

The TX-7700 which I got is manufactured for Japan and because of that it is designed to work with 100V AC and frequency range is limited to 76MHz to 90MHz. In this quick post, we demonstrate how to tune this stereo receiver to 88MHz to 108MHz by without modifying the circuit(s) of the tuner.

In this tuner, the main component which needs to adjust is 5 turn inductor located in FM front end circuit (refer A in below photograph). The frequency range of the tuner can be adjusted by changing the spacings of this inductor. If tuning is getting difficult, slightly adjust the trimmer capacitor in that module (marked as B in the same photograph).

FM front end components to adjust.

After carefully adjusting the inductor and trimmer capacitor we were able to tune TX-7700 into 88MHz -108MHz frequency range. Once the receiver is desired frequency range the clarity of the reception can adjust by turning the compression trimmers located in tuning capacitor (refer C and D in below photograph).

Trimmer capacitors of FM tuner stage.

This method can be used to tune any analog (FM) tuner which has an identical design to TX-7700.

Comments

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...