Restoring Sony STR-AV780 AV receiver

Sony STR-AV780 is a combined receiver and audio/video control center. This receiver is manufactured by Sony in around 1986 and it is capable to deliver 2 × 80W audio output power with 8Ω speaker load.

The STR-AV780 which I got had two problems. The first problem is in the power amplifier stage and it produces distortion in high frequencies. The second problem is in FM radio receiver and it is completely dead.

The power amplifier of STR-AV780 is based on two Sanyo STK4042 XI AF power amplifier ICs. To fix the distortion issue we replace all the electrolytic capacitors in both STK4042 power amplifier boards. After replacing capacitors distortion issue got fixed and the power amplifier starts to produce a clear output waveform.

The FM receiver of this AVR is mainly based on 2 ICs. For IF stage it uses LA1235, and to demodulate FM stereo signal it uses LA3401. Apart from that Sony CX7925 is used as PLL frequency synthesizer. The front end of FM tuner is based on a couple of transistors and FETs.

To fix FM receiver we inject FM test signal into the receiver and check each stage of the FM receiver. Based on VCO output (of CX7925) and FM front end output we identify LA1235 as a faulty component. After replacing LA1235, FM tuner starts to work again.

Fixed AV780 mainboard - tuner stage.

Due to the weak nature of PCB copper tracks, we attach LA1235 into the main PCB through an IC base.

After replacing all above-described components we clean and repaint the entire AV receiver.

During test stages, we check this receiver with several speaker setups. Out of all the speakers, this receiver performs extremely well with our Pioneer CS-707 speaker system.

Due to lack of service manual / schematic Sony STR-AV780 is a quite difficult receiver to repair. We trace and fix components of this receiver based on PCB layout and IC data-sheets.

Comments

Anonymous said…

Any ideas on what to do if the display doesn't always seem to work.
There are days that when it is first turned on it will work from a few minutes to maybe an hour. But then it goes dark.

Thanks.

August 24, 2019 at 10:17 AM

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...