Arduino interface for TFA9842AJ Power Amplifier

TFA9842AJ is quiet old 7.5W audio power amplifier introduced by NXP. This amplifier IC is no longer produced by NXP, but still, it's available to purchase in many places, which including eBay, AliExpress, Amazon, etc.

NXP TFA9842AJ Power amplifier IC.

I tested a couple of TFA9842AJ based amplifiers in the last couple of years. The main reason I liked TFA9842AJ is its simple, clean design, wide operating voltage, and high-quality bass-rich audio output.

Thanks to it's built-in DC volume control circuit this audio amplifier can easily interface with MCU. In this article, we provide a generic TFA9842AJ module which works with most of Arduino boards, MCUs and SOCs.

Schematic of the TFA9842AJ module.

As illustrated above, this system consists of LM321 operational amplifier and TFA9842AJ IC. To support both 5V and 3.3V logic inputs we introduce logical level selection jumper (J2) into this design. To control the volume PWM input must apply to the J1.

In this system volume of the power-amplifier is proportional to the duty cycle of the PWM input. In 0% duty cycle the amplifier is in standby mode. At 100% duty cycle it performs with its maximum gain.

This module is designed to work with 12V 3A DC power source. At the testing stages, we share this power source with the Arduino board.

We successfully test this module with the following development boards and MCUs:

Arduino UNO
Arduino MEGA 2560
Arduino Due
Orange Pi 3
ATmega8
ATmega328
ATmega640

In Arduino platforms, we produce PWM output using analogWrite() function. In other platforms and ICs, we generate PWM output using inbuilt hardware PWM generators.

In this design, we use SMD components to miniaturize this module. If you plan to build this using through-hole type components, use LM358 as an operational amplifier (U1).

This module is released under the terms of CC BY 4.0. The KiCad design files of this module are available to download in here.

Comments

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...