Experimental motor driver for CG-4 German equatorial mounts

This is an experimental stepper motor driver for Celestron CG-4 German equatorial mounts. This unit is functionally equivalent to the Celestron dual-axis motor driver, and we developed it as a replacement unit for the original Celestron driver.

The prototype circuit board of the motor controller unit.

The core component of this motor driver is PIC16F88 8-bit MCU. This MCU is responsible for driving two motors and scanning the user inputs. As an original unit, this system also got a clock driver for the right ascension (RA) axis.

This system uses two L293 motor drivers to drive the right ascension (RA) axis and declination (DEC) axis motors. This unit is designed to work with 6V bipolar stepper motors, which include in the telescope mount. The LM350 voltage regulator is used to maintain power to both stepper motors.

Internal view of the prototype enclosure.

This replacement motor drive provides all the functionalities of the original unit, which including manual right-ascension and declination movement controls, speed, and direction controls.

Final view of the prototype unit.

We design this unit at the COVID-19 lockdown period, and therefore this prototype we used components which already available in our inventory. A component-wise this prototype is not an efficient design. The main objective of this design is to experiment with the motor driving mechanism and timing. Later we intend to design a more effective and feature-rich controller with the collaboration of digitspace.com.

The schematic and firmware source of this project is available at https://github.com/dilshan/eq-motor-driver.

Comments

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle. In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...