Skip to main content

Mullard 3-3 Amplifier Project (Part 2)

This is a second article related to Mullard 3-3 Amplifier Project and in this article, we introduce HT transformer and HT power supply related to this amplifier. As mentioned in the previous post, the power supply unit of this tube amplifier is constructed using 400V 5A bridge rectifier, 220µF (400V) and 82µF (400V) electrolytic capacitors.

Homebrew HT transformer and PSU

The most vital component of this power supply is the HT transformer and due to limited availability, we construct this transformer by ourselves. We construct this transformer to obtain the following voltages and primary winding is design for 230V AC mains lines.

Winding Voltage Current
HT Winding 210V 100mA
Filament Winding 6.3V 1.5A

Winding parameters for this transformer is listed in below tables:

Core Size 1inch2
Winding Turns Wire
Primary Winding 1725 32 S.W.G
Secondary Winding (210V) 1650 34 S.W.G
Secondary Winding (6.3V) 44.5 21 S.W.G

To reduce noises we build shielding layer in between primary and secondary winding with 32 S.W.G enameled copper wire and connected it to transformer laminations/ground.

To get stability and safety we recommended applying isolation tape layers in between each winding of this transformer.

Winding details of this transformer are calculated using Python script available in here.

During our tests, this transformer and PSU performs extremely well with our Mullard 3-3 amplifier unit and we really impressed with its higher audio quality.

Please note that electrolytic filter capacitors in this PSU hold lethal charges. Be sure to discharge them before working on PSU or amplifier unit. To discharge, connect 10K - 100K resistor to output terminal and leave it for few minutes.

Comments

Popular posts from this blog

CD2003 - yet another simple FM radio receiver

In the last few days, we are looking for some simple FM radio receiver to integrate into one of our ongoing projects. For that, we try several FM radio receiver ICs including TDA7000, CD2003/TA2003/TA8164, CXA1019, and KA22429. Out of all those chips we select CD2003 (or TA2003/TA8164) based receiver for our project because of its simplicity and outstanding performance. Except to CD2003, Sony CXA1019 also perform well but we drop it because of its higher component count. We design our receiver based on Toshiba TA2003 datasheet and later we try TA8164 and CD2003 with the same circuit. Either CD2003 or TA8164 can directly replace TA2003 IC, and as per our observations, TA8164 gives excellent results out of those 3 chips. A prototype version of CD2003 FM radio receiver The PCB design and schematic which we used in our prototype project are available to download at google drive (including pin-outs of crystal filters and inductors ). Except for CD2003 IC, this receiver consist...

Arduino superheterodyne receiver

In this project, we extend the shortwave superheterodyne receiver we developed a few years ago . Like the previous design, this receiver operates on the traditional superheterodyne principle.  In this upgrade, we enhanced the local oscillator with Si5351 clock generator module and Arduino control circuit. Compared to the old design, this new receiver uses an improved version of an intermediate frequency amplifier with 3 I.F transformers. In this new design, we divide this receiver into several blocks, which include, mixer with a detector, a local oscillator, and an I.F amplifier. The I.F amplifier builds into one PCB. The filter stage, mixer, and detector stages place in another PCB. Prototype version of 455kHz I.F amplifier. In this prototype build, the Si5351 clock generator drives using an Arduino Uno board. With the given sketch, the user can tune and switch the shortwave meter bands using a rotary encoder. The supplied sketch support clock generation from 5205kHz (tuner f...

Calculator for audio output transformers

Audio output transformers are heavily used in a vacuum tube and some (older) transistor base audio power amplifiers, but these days output transformer are quite hard to find and expensive item. For homebrew projects, the best option is to construct those transformers by ourselves and this script helps to calculate winding parameters for those transformers. This " AF output transformer calculator " script is written using Python and it works with most of the commonly available Python interpreters . The script is available to download at google drive under the terms of GNU General Public License version 3.0 . Homebrewed 25k: 4 output transformer Once supplied the input parameters this script provides a winding ratio, the number of turns required for primary and secondary winding and required copper wire gauges for both primary and secondary windings, etc. We construct several AF output transformers based on results of this script, which including transformers for M...